Reasons to install an underlayment

Reasons to install an underlayment

Underlayments are an important aspect of a flooring project, in both residential and commercial settings, where a level and smooth surface is required before installation of the final floor covering. The type of underlayment needed will depend on what kind of flooring will be installed on top of it. Other considerations include the size of the area, its purpose, and how much foot traffic it will see.

Underlayments are installed on top of a subfloor to level the surface, creating a perfectly smooth, level finish. When it comes to floor coverings such as vinyls or laminate flooring, it is very important to eradicate imperfections in the subfloor as this will impact the aesthetic and longevity of the installation. Large format tiles may be slightly curved and therefore a level surface will reduce the ‘lipping’ that may occur when installing these tiles.

An underlayment must be covered with a final floor covering. If you want a concrete-look floor then a decorative overlayment is required such as TAL SuperFlow or TAL Fusion

Additives

An additive is a latex-based liquid, designed to replace water in a cement-based adhesive and / or grout mix which is used when tiling or grouting external areas, wet areas, high traffic areas and areas where some flexibility is required. Our range of additives includes TAL Bond and TAL Screedbinder. 

Additives aid in water-resistance while increasing the flexibility of the adhesive and grout. For this reason, adding an additive to the grout mixture when you are installing tiles in wet areas, such as showers, and exterior applications is imperative. When TAL Screedbinder is added to TAL Superscreed, its bond strength and flexibility is improved. If you mix TAL Screedbinder with TAL Superscreed, the screeding compound can be used as a protective barrier under ceramic tile heating elements.

When using an additive in the adhesive or grout mixture, it is important to use the full amount of additive as stipulated in the instructions on the packaging. Never dilute the mix with water as this will compromise the latex, which affects the flexibility and water-resistance of the adhesive or grout.   Also remember, the additive is always used as a water-replacement in the mix.

Step 2. In the meantime, plan the layout of the mosaic sheets and cut them to fit around the waste.

Tip: For enhanced flexibility and water resistance, it is recommended that the adhesive water mix be replaced with TAL BOND. This is important in installation areas that will be exposed to water, heat and humidity. Add TAL MOSAICFIX  to the liquid and mix well to a creamy, lump-free consistency. Let it stand for three minutes and stir again.

Step 3. Once mixed well, apply the adhesive to the surface in a solid bed of 4 mm to 6 mm, working in small areas of a square metre at a time. 

When  using  large  format  tiles (a  tile  with  the  length of at least  one  edge equal to/greater  than  600mm, or a facial area greater than  3500cm²) there will be a smaller number of grout joints, compared with the same area of normal format tiling. As a result, less stress (movement) can be accommodated at tile joints.

Considering a wood-look tile installation? Give us a call or send usan email and we’ll give the right advice, no matter how big or small your tile installation: 0860000 TAL (825) or [email protected]. If this TAL Talk blog post interested you, you may want to take a look at this TAL Talk blog post: The 101 on wood-look tiles.

Step 4. Bed the mosaics immediately, pressing them firmly into the adhesive. Use a wooden beating block or rubber grouting float to tap them in and create a level surface. Using tile spacers between the individual mosaic sheets will maintain the joints

Step 5. Allow the adhesive to squeeze through the joints between the mosaics to form the grout and, if necessary, fill in any low areas in the joints with extra adhesive. 

Step 6. Clean the excess adhesive off the face of the mosaics gently with a lightly dampened sponge, and leave to dry for a few hours.Work carefully to ensure that the mosaic installation is not disturbed, and that the glass mosaics are not scratched during application and cleaning. Polish the mosaic tiles with a dry cloth to remove any grout haze.

Step 7. Apply a silicone sealant to all the perimeter joints.

TAL MOSAICFIX is available in 20 kg and 5 kg bags from leading retail outlets. 

Designed to be 100% compatible, using the TAL range of products ensures fully guaranteed multi-level tiling systems from a single source. TAL products are manufactured in South Africa to suit local climatic conditions.

If you are in any doubt, contact the TAL Technical Advisory Service on 0860 000 TAL (825), email [email protected]. Alternatively, employ the services of an experienced and skilled mosaic tiling contractor.

When replacing tiles, it is not always possible to apply the TALFIX directly to the floor, in which case apply the adhesive in a solid bed onto the back of the tile, ensuring complete coverage. Gently trace the notched side of a floor trowel through the adhesive to create ‘ridges’.

Adhesive system

When tiling onto existing tiles, it is important to only use a quick- or rapid-setting adhesive, as the existing tiles will present a dense, impervious surface, and standard-setting adhesives will take longer to dry. Too early trafficking of newly-installed tiles before the adhesive has set sufficiently can result in hollow-sounding or loose tiles.

Use TAL Tile-To-Tile quick-setting adhesive for tiling onto interior surface beds. When tiling onto suspended slabs and for external installations mix the TAL Tile-To-Tile with TAL Bond, replacing the water in the mix. Alternatively, TAL Bond Powder can be added to the adhesive mixing water.

Ensure that there is a solid bed of adhesive at least 6 mm thick beneath each tile.

Back buttering with a thin coat of adhesive may also be required when using large-format tiles to ensure full contact with the adhesive bed.

Grouting

Grouting should not be carried out until the adhesive has set sufficiently to prevent the tile installation from being disturbed during the grouting operation (always refer to the adhesive packaging for setting times). When using TAL TAL Tile-To-Tile, allow a minimum of six hours before grouting.

For interior surface beds, use TAL Wall & Floor Grout for filling tile joints up to 8 mm wide. TAL Quarry Grout can be used in wider joints up to 25 mm wide. On suspended slabs and for external installations, replace the water in the grout mix with TAL Bond, or add TAL Bond Powder to the grout mixing water.

Particular care must be taken to clean the grout off the tile face before it hardens completely. This is especially important when an additive such as TAL Bond or TAL Bond Powder has been used. A tile sample should be tested beforehand to ensure that no grout is absorbed through the glaze or into the tile body, thereby staining the tiles permanently.

Movement joints

The lack of movement joints in tile installations is a major cause of tile failure. When tiling over existing tiles, the existing structural and movement joints must be maintained in the new tile installation. The movement joints should be at least 5 mm wide and extend through the adhesive and both tile layers.